ELTEK VALERE ATION PASSWORD IS 5001
ELTEK VALERE ATION MANUAL VERY CAREFULLY

Eltek Valere Ation Manual Very Carefully

ATTENTION Read this manual very carefully before installing and commissioning the specified module. ELTEK VALERE DEUTSCHLAND GmbH. 10 Installation And Operation Manual Low Power (LP) DC Power SystemUser Manual Page 2 (28) В©2009. 5/16 box wrenches, sockets, and/or nut drivers. O 1 & 2 Flat head and Phillips screwdrivers. Eltek Valere systems are designed to be installed with a minimum number of commonly available tools.

No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical, including photocopying and recording for any purpose without the explicit written permission of Eltek Valere. Additionally to this ebook, on our site yourepresent a commitment on the part of Eltek Valere. You can read Eltek smps 700 manual online either load. We present full release of this book in doc, DjVu, PDF, ePub, txt forms.

If you desire, enter a session name and press the Save button for easy loading in the future.Once the settings are accurate press the Open button. 2.1 PuTTY The main screen can be seen in Figure 1.To use, enter in the IP address of the Valere LAN Module and ensure that the Telnet option is selected. Any Telnet program will work in place of PuTTY.

Eltek Valere Ation Password Is 5001

Use the following sections for additional commands 3 General Commands The following categories list all the different commands available via the Telnet session. To complete your Telnet session, type in logout and the Telnet session will end. From the command prompt, type help for a short list of commands In addition, the results of each command entered will be one of the following: REQUEST_OK or REQUEST_FAIL. If login is not successful the application will exit. If successful you will see the system identifier command prompt:Unassigned> Note: A unique name can be created for the system. The default username is Admin, and the default password is 5001.

Adjustments are added to the current RTC setting. Example: To set the system Preset to Preset A use the following command Unassigned>set system PresetA System CommandsVerb Object Token Data Description Responseget system location Returns system identifierSet system location XX = a valid Location/System Identifier Name with a 20 character limit Request_OKGet system state System State :: System Normal/Alarmget system voltage voltage = Xget system current current = Xget system alarm System OK = any active alarmGet system presetCurrent parameters based on configuration: preset = Preset X (X is the desired preset value)Set system preset X X = Preset A, Preset B, or Preset C Request_OKget system DateTime DateTime = Day, MM/DD/YYYY, HH:MM:SSset system DateTime X X = MM/DD/YYYY HH:MM:SS Request_OKRTC Calibration (seconds) = X. 3.1 System Commands System commands will allow the user to view and change general system setpoints such as float voltage and alarms. The user thenCan use the object in the command get object help for a list of tokens for that object. This command will provide the user with a list of objects. Commands are available within the Telnet session by using the command get help.

Presets are factoryDefined values that are not user settable. Internally it is converted into a nuSet system AdjustClock X X = +326 to -164 Request_OKGet system infoLocation, State, Voltage, Current, Type, Battery Current, Runtime, Alarms (if any)Retrieves system Vmax, Vmin, Imax, Imin, IBmax, IBmin, Tmax, TEmax, TEmin, ACF for a 24 hour periodGet system pm15MinuteRetrieves system V, ILoad, IBat, AmbT, ExtT, ACF for every 15 minutes in a 24 hour periodGet system pmdataRetrieves system V, ILoad, IBat, AmbT, ExtT, ACF for every 15 minutes in a 24 hour periodThe following system tokens are available by entering: get system help location The user defined name of the controller state The current system state, either System Normal or SystemAlarm voltage The current system voltage current The system current alarm Displays any active system alarms preset The most recently activated Preset. A value of 0 (zero) resets calibration to none.

Example: To set the internal over temperature setpoint to 90 C use the following command Unassigned>set temp inthighlimit 90 Temperature CommandsVerb Object Token Data Description Responseget temp internal internal = X degree C/FProbeY = enabled, disabled, EnclAlarm, DistAlarm, X degree C/F, or removedGet temp allinternal = X degree C, probe1-4 = enabled or disabledGet temp unit unit = degree C or Fset temp unit X X = C or F Request_OKGet temp intlowlimitany valid temperature value between 30C/86F and 93C/199FGet temp inthighlimitany valid temperature value between 30C/86F and 98C/208FGet temp extlowlimitany valid temperature value between 30C/86F and 93C/199FGet temp exthighlimitany valid temperature value between 30C/86F and 98C/208FProbeYType = disabled, TProbe, Encl NO, Encl NC, Dist No, or Dist NCX = disabled, TProbe, Encl NO, Encl NC, Dist NO, Dist NC Request_OKThe following temperature tokens are available by entering: get temp help internal Displays the internal temperature value (degree of 22 Version 1.

Eltek Valere Installation Manual